Ενα πολυ καλαο και τιμιο για τα λεφτα του radio.
Πολυ ωραια οθονη, φωτεινη και δεν χαραζει ευκολα.
Θα το αγοραζα ξανα.
Ευχαριστω

Ενα πολυ καλαο και τιμιο για τα λεφτα του radio.
Πολυ ωραια οθονη, φωτεινη και δεν χαραζει ευκολα.
Θα το αγοραζα ξανα.
Ευχαριστω

Ενα πολυ καλαο και τιμιο για τα λεφτα του radio.
Πολυ ωραια οθονη, φωτεινη και δεν χαραζει ευκολα.
Θα το αγοραζα ξανα.
Ευχαριστω

• 
• 
• 
• 
• 

• 
• 
• 
• 
• 

Rotate left Rotate right

Очередная модификация платформы 70ххВ на процессоре AllWinner F1C200s.
Автомагнитола пришла со склада в России за 3 ДНЯ, привез курьер IML!
Но пришлось сразу её разбирать по причине плохого качества зачистки задней стенки
(Все щели были в жутких задирах из алюминия! Чистил напильником и метал.щеткой и
продувал воздухом смотри последнее фото). Потом отмывал флюс и капельки припоя с платы кнопок.
Главная плата чистая! Что порадовало. Версия главной платы новее (2019-11-08),
чем самой прошивки (2019-01-16). Сделал редактирование исходной прошивки дамп сам снимал для страховки от сбоев. Теперь в прошивке есть выбор УЖЕ 22 ЛОГО АВТО, а не только из 6 логотипов как исходная.
MirrorLink работает на Android 8.0 c Sharp C10.
Из-за скудного описания долго проверять распайку шлейфов и проводов, После подключения всё заработало нормально. Усилитель TDA7388, предусилителя типа ТДА7313 нет вообще, MCU 101 даташита нет в инете, Радио ловит без антенны на кусок провода. Видеовходы принимают сигнал с видеокамеры. Камеру заднего хода не подключал. Пульт ДУ управляет хорошо. По загрузке при игре флешек и SD карт - ток 0,65 А, просмотр видеороликов и прослушивание FM-радио - ток уже 1,65- 2,0 А, из-за чего сильно греется задняя стенка. Буду позже ставить усилитель TDA7580 и конденсатор на 10000 mF.

Another modification of the 70xxV platform on the AllWinner F1C200s processor.
The car magneto came from a warehouse in Russia for 3 years, brought a courier IML!
But I had to disassemble it right away because of the poor quality of the rear wall sweep.
(All the slits were in creepy bullies made of aluminum! Cleaned with a file and metal.brush And
was blown by air see the last photo). Then he laundered the flux and solder droplets off the board of buttons.
The main fee is clean! That pleased. Main Board Version is newer (2019-11-08),
than firmware itself (2019-01-16). Made the editing of the original firmware dump itself removed for insurance against failures. Now the firmware has a choice of ALL 22 LOGO AUTO, instead of only 6 logos as the source.
MirrorLink runs on Android 8.0 with Sharp C10.
Due to the meagre description, it took a long time to check the unbuttoning of the plumes and wires, after the connection everything worked normally. Amplifier TDA7388, pre-amplifier such as TDA7313 is not available, MCU 101 is not in the Internet, Radio catches without antenna on a piece of wire. The video inputs are picking up the signal from the video camera. No reverse camera. The remote control controls well. On loading during the game flash drives and SD cards - current of 0.65 Am, watching video clips and listening FM-radio - current is already 1.65- 2.0 Am, because of which the back wall is very warm. I will later install the TDA7580 amplifier and capacitor at 10000 mF.

Another modification of the 70xxV platform on the AllWinner F1C200s processor.
The car magneto came from a warehouse in Russia for 3 years, brought a courier IML!
But I had to disassemble it right away because of the poor quality of the rear wall sweep.
(All the slits were in creepy bullies made of aluminum! Cleaned with a file and metal.brush And
was blown by air see the last photo). Then he laundered the flux and solder droplets off the board of buttons.
The main fee is clean! That pleased. Main Board Version is newer (2019-11-08),
than firmware itself (2019-01-16). Made the editing of the original firmware dump itself removed for insurance against failures. Now the firmware has a choice of ALL 22 LOGO AUTO, instead of only 6 logos as the source.
MirrorLink runs on Android 8.0 with Sharp C10.
Due to the meagre description, it took a long time to check the unbuttoning of the plumes and wires, after the connection everything worked normally. Amplifier TDA7388, pre-amplifier such as TDA7313 is not available, MCU 101 is not in the Internet, Radio catches without antenna on a piece of wire. The video inputs are picking up the signal from the video camera. No reverse camera. The remote control controls well. On loading during the game flash drives and SD cards - current of 0.65 Am, watching video clips and listening FM-radio - current is already 1.65- 2.0 Am, because of which the back wall is very warm. I will later install the TDA7580 amplifier and capacitor at 10000 mF.

• 
• 
• 
• 
• 
• 
• 

• 
• 
• 
• 
• 
• 
• 

Rotate left Rotate right